FACTSHEET

ISDN-Board SX2 SinglePRI and DualPRI, replaces HST Saphir V (kb2895)

The information in this article applies to:

  • SwyxWare v4.40
  • SX2 DualPRI
  • SX2 SinglePRI
  • HST SAPHIR V-B Primary PCI
  • HST SAPHIR V Primary PCI

[ Summary | Information ]


Summary

Version V4.40 of SwyxWare will introduce two new ISDN-Boards. These boards are called SX2 SinglePRI and SX2 DualPRI and include 1 or 2 PRI interfaces. SX2 SinglePRI and SX2 DualPRI will replace the legacy ISDN-Board HST Saphir V (1xPRI).

Information

Version V4.40 of SwyxWare will introduce two new ISDN-Boards. These boards are called SX2 SinglePRI and SX2 DualPRI and include 1 or 2 PRI interfaces. SX2 SinglePRI and SX2 DualPRI will replace the legacy ISDN-Board HST Saphir V (1xPRI).

SX2 SinglePRI
SX2 SinglePRI
Click to enlarge...

SX2 DualPRI
SX2 DualPRI
Click to enlarge...

Both boards use the Cologne Chip HFC-E1. It is designed especially to be used with SwyxWare and manufactured exclusively for Swyx.

FEATURES

  • 1 x PRI (SX2 SinglePRI) resp. 2 x PRI (SX2 DualPRI)
  • each port can be configured separately to TE/NT mode with a Jumper field
  • line-termination (120 Ohm resp. 75 Ohm) is independently selectable for each port by DIP switch
  • up to 4 cards (SX2 QuadBRI, SX2 SinglePRI and SX2 DualPRI) can be installed in one PC, up to 76 B-Channels per PC are supported. Sx2 DualPRI counts as two cards, it will also show up as two network devices in the windows device administration.

PCI interface

  • PCI interface is suitable for 3.3V as well as 5V PCI 2.x slots (5V to 3.3V regulator on board)

PCM Highway

  • clock synchronization between SX2-boards is possible using flat ribbon cables. This option will be supported by the driver in Q2/2006. The cable will be availbe in Q2/2006 as well.
  • 2/4/8 Mbit/s data transfer rate

Chipset

  • Cologne Chip HFC-E1 chip
  • high precision 32.768 MHz quartz oscillator
  • 512 x 8 bit serial EEPROM for the programming of PCI configuration information

General purpose I/O

  • 2 red and 2 green LEDs at the slot bracket per PRI-Interface
  • 4-DIP switch per PRI-Interface can be checked by software for e.g. clear identification of the card

SX2 SinglePRI Retaining Bracket
SX2 SinglePRI Retaining Bracket
Click to enlarge...

SX2 DualPRI Retaining Bracket
SX2 DualPRI Retaining Bracket
Click to enlarge...

additional Information

  • The legacy ISDN-Board HST Saphir V will be avaible and delivered for some weeks after the release of V4.40 als long our stock lasts.
  • The new SX2 SinglePRI and SX2 DualPRI use an new driver (available on our Website and is included in the SwyxWare V4.40 CD, the board will work with SwyxGate version V4.33 or newer.
  • SX2 SinglePRI and SX2 DualPRI cards do not support T.30-Fax Transmission, e.g. only SwyxFax V2.00 or newer can run on these cards.  

Comment

Comment on this article



If we have any follow-up questions, where can we contact you?

E-Mail Address (optional)


Note

This feedback form can't be used for support requests. Those requests must be directed to your Swyx reseller or distributor.